1. Turn on the device you wish to control (TV, VCR, cable box, satellite receiver, etc).

2. Press and hold SETUP until the LED indicator lights steadily. Release the SETUP button.

3. Press and release the mode button that matches the device you want to control. The LED blinks once. Use AUX for audio equipment.

4. Enter the 3-digit code from the library code tables. The LED turns off after the last digit entered.

5. Point the remote at your device and press the POWER button. Your device should turn off.

6. Turn your device on and press CHANNEL+. If the device responds, setup is complete.
   Notes:
   
   • For audio equipment (CD, stereo, etc.) use the AUX button.
   • If your TV/VCR/cable box/satellite receiver does not respond, try the other codes for your brand. If it still doesn't respond, try the code search method, described below.
   • If the LED blinked rapidly when you entered the code, you may have entered an invalid code. Recheck the code in the code list and try again.
   • If some buttons do not operate your device, try one of the other codes for your brand.

Using AUX to control a second TV, VCR, cable box or satellite receiver:

Although the AUX button is normally used to control an audio component such as a CD or stereo system, it can also be configured to control a second TV, VCR, cable box or satellite receiver instead.

1. Turn on the equipment you wish to control.

2. Press and hold SETUP until the LED indicator lights steadily. Release the SETUP button.

3. Press the AUX button, then press the mode button that matches the equipment you wish to control (TV, VCR, CBL, SAT).

4. Press and release the mode button that matches the A/V equipment you wish to control. The LED blinks once.

5. Enter the 3-digit code from the library code tables. The LED turns off after the last digit entered.

6. Point the remote at your audio component and press the POWER button. Your audio component should turn off.

7. Turn your audio component on and press CHANNEL+. If it responds, setup is complete.
   Notes:
   
   • If your audio equipment does not respond, try the other codes for your brand. If it still doesn't respond, try the code search method, described below.
   • If the LED blinked rapidly when you entered the code, you may have entered an invalid code. Recheck the code in the code list and try again.

Searching for codes:

1. Turn on the device you wish to control.

2. Press and hold SETUP until the LED indicator lights steadily. Release the SETUP button.

3. Press and release the mode button that matches the device you want to control. The LED blinks once.

4. Press the CHANNEL+ repeatedly until the device to be controlled changes channel. You may have to press CHANNEL+ many times (perhaps 50 or more). If the device does not have a Channel Up function, use the PLAY button (VCR only) or the POWER button.

5. Press and release the ENTER button to complete the setup.

Identifying codes found using the search procedure:

1. Press and hold SETUP until the LED indicator lights steadily. Release the SETUP button.

2. Press and release the mode button that matches the device you wish to identify. The LED blinks once.

3. Press and release the SETUP button. The LED blinks once.

4. To find the first digit, press each number button, from 0 to 9, until the LED blinks. The number you pressed is the first digit of the code.

5. Press each number button, from 0 to 9, again as above to find the second digit.

6. Press each number button, from 0 to 9, again as above to find the third digit. When the third digit has been found, the LED will go out.

Setting the sleep timer:

The sleep timer automatically turns off the TV after the time you set (1 to 99 minutes).

1. Press and hold SLEEP until the LED indicator lights steadily. Release the SLEEP button.

2. Use the number buttons to enter the sleep time required (1 to 99 minutes).

3. Press ENTER to confirm the setting.

Take care to leave the remote pointing at the TV to ensure it turns off the TV at the time you set.

Controlling X10 modules:

If you have already installed the Transceiver Module, you can control it and other X10 modules as follows.

1. Press and release the X-10 button.

2. Use the number buttons to enter the Unit Code number of the chosen module. You do not need to enter zero '0' for single digit numbers.

3. Press the appropriate button for the function you require:

   On:	CHANNEL+
   Off:	CHANNEL-
   Bright:	VOLUME+
   Dim:	VOLUME-
   All Lamps On:	POWER
   All Lamps Off:	MUTE

You cannot dim or brighten an Appliance Module. If the module was off and you press its unit code followed by Bright or Dim (VOLUME+ or VOLUME-) this will simply turn the module on.

Setting the X-10 sleep timer:

The X-10 sleep timer switches off the chosen modules after the preset time.

1. Press and release the X-10 button.

2. Press and hold SLEEP until the LED indicator lights steadily. Release the SLEEP button.

3. Use the number buttons to enter the module Unit Code for the module to be turned off.

4. Press the desired function button (e.g. CHANNEL- to turn the module off after the preset time).

5. Use the number buttons to enter the sleep time required (1 to 99 minutes).

6. Press ENTER to confirm the setting.

Changing the X-10 House Code:

The SuperRemote defaults to House Code A, and in most cases you will not need to change this unless you are experiencing interference from a neighboring X-10 system.

1. Press and release the X-10 button.

2. Press and hold SETUP until the LED indicator lights steadily. Release the SETUP button.

3. Use the number buttons to enter the number equivalent to the chosen House Code (1=A, 2=B...16=P).

The House Code you choose must match the House Code on the Transceiver Module and the ActiveHome software you are using it with.

Controlling an IR Mini Controller:

If you already own an IR Mini Controller, you will need to change the X-10 Home Automation code in the remote to use it. The code for standard X-10 Home Automation is 013. The code to control the IR Mini Controller is 014. To change the code:

1. Press and hold SETUP until the LED indicator lights steadily. Release the SETUP button.

2. Press and release the X-10 button.

3. Enter the 014 to control an IR Mini Controller, 013 for standard X-10 control. The LED turns off after the last digit is entered.

In most cases, you will not need to use the IR Mini Controller to receive commands from the remote — the Transceiver Module does this for you and has the added advantage of working through walls. You can't control the IR Mini Controller and the Transceiver Module at the same time.